Speedheater™ Standard 1100 Kit Infrared Paint Remover

Here is a comparison to help you choose between the Speedheater 1100 Standard, Speedheater Cobra, and Rapid Slim. Quick Comparison

We are located in Virginia. Here is a UPS map showing shipping times for your specific state. Please add one day for processing.

Everything posted is in stock unless indicated as a Back order.

Infrared works on the oil present in paint. If the oil has evaporated over time, putting a coat of linseed oil on it will help rejuvenate the paint.

We wouldn’t say it’s faster. It’s more effective. Please note that most of the time it’s not necessary to apply it.

The best unit for floors is the Speedheater 1100. You can place the unit’s side plates directly on the surface. This heats a large area . While scraping the first heated area, the next section can be heated.

Yes, it does. Just make sure to be more gentle when scraping the paint off the surface.

Yes, infrared heat will soften fiberglass. However, when stripping fiberglass, it is challenging to avoid scraping and damaging the layers beneath, such as on a boat’s fiberglass hull. Gentle scraping is necessary.

We wouldn’t say it’s faster. It’s more effective. Please note that most of the time it’s not necessary to apply it.

The best unit for floors is the Speedheater 1100. You can place the unit’s side plates directly on the surface. This heats a large area . While scraping the first heated area, the next section can be heated.

Yes, it does. Just make sure to be more gentle when scraping the paint off the surface.

Yes, infrared heat will soften fiberglass. However, when stripping fiberglass, it is challenging to avoid scraping and damaging the layers beneath, such as on a boat’s fiberglass hull. Gentle scraping is necessary.

The three units have different heat concentrations and different heated areas. We recommend a unit based on the nature of your project.

First of all, check if the overheat button popped out. If that does not work, call our Repair Center at: (908) 230-8218

You can remove tar with infrared heat. Tar will likely be very sticky when heated. The scrapers may need to be cleaned often.

Veneer is glued onto the base wood. The infrared rays heat some of the base wood, the glue, the veneer wood, and the varnish or paint. Therefore, it is too difficult to scrape the coating off without damaging the veneer. Although we do not like chemical strippers, as they can be harsh on the wood, it is easier to control how many layers of coating are removed. We recommend SOY GEL Paint Stripper, made by Blue Bear, as a more gentle, “Green” liquid stripper.

Likely, the paint will soften, but scraping without damaging the tile surface would be difficult. We recommend a chemical stripper if this is the only project you have on your list.

Infrared heat might work on metal. But it depends on how thin the metal is. The thicker the metal, the less likely IR will heat all the paint layers for scraping.

The infrared heat may soften the paint on bricks or stone. However, scrapers can only remove the top surface coating. The paint in the pits of the bricks or on irregularly surfaced stone might still remain. Some people report success using a wire brush after the surface paint has been heated and removed.

 Yes but lots of dry scraping back and forth might be needed.

Yes, but like milk paint, lots of dry scraping will be needed.

The Speedheater™ does remove thick paint from plaster, most of the time. We cannot say yes with the same certainty as we do with paint on wood. If the paint is very thick, it likely will work. If the surface is very rough and not smooth, the scraping would be difficult. We do have customers who have used it successfully on plaster ceilings.

We recommend using our Protection Aluminum Mat. It is ideal for safeguarding areas you don’t want affected by Infrared heat.

We recommend using our Protection Aluminum Mat. It is ideal for safeguarding areas you don’t want affected by Infrared heat. You can also make a shield by covering a 5” X 12” piece of wood with aluminum foil.

It may if the paint is thick.  Test an area first. We recommend using a wire brush once you get to the porous/delicate nature vs concrete – it depends on how soft the paint is and the effectiveness of the brushes used to remove.

Moderate mess – The paint softens and comes off in larger, pliable strips or chips rather than turning into dust.

Easier cleanup – Scrapings can be collected on a plastic sheet nd safely bagged. This is especially important if lead paint is present.

Less airborne debris – Unlike sanding, there’s almost no dust, which keeps your worksite cleaner and safer.

Yes, but only if misused. If you hold the tool too close for too long, especially with the Speedheater™ Cobra (which works very quickly), the surface can scorch or darken. Read the manual instructions to learn the recommended heating time.